In this guide
The short answer is 100mm. The longer answer is that 100mm clearance is the minimum, and a car can sit above it and still be illegal if the drop eats too much suspension travel, the tyres foul the guards, or the total change is past 50mm without engineering.
Here's how the national code and the states actually define a legal lowered car.
Quick answer: Keep at least 100mm ground clearance (wheels, tyres and mudflaps excluded). Without engineering, VSB 14 allows a total height change of up to 50mm and no more than one third of original suspension travel. Front and rear should drop by the same amount, tyres can't touch the body at full lock or bump, and bump stops stay in. Go further and you need a certifier.
The national baseline: VSB 14 Section LS
Most states build their suspension rules on Vehicle Standards Bulletin 14 (the National Code of Practice for Light Vehicle Construction and Modification), Section LS. It sets out what you can do without certification and what needs an engineer.
What you can do without certification
VSB 14 lists "lowering and raising suspensions (by not more than one third of the original suspension travel and provided the original vehicle height is not increased or decreased by more than 50mm)" as a basic modification. That 50mm is the total change from all modifications combined. Lower wheels and tyres count toward it too.
The one-third rule
When lowering, unladen ride height must not change by more than one third of the working suspension travel, measured from original height to the manufacturer's rigid bump stop, with deformable stops removed. Put another way, the code wants at least two thirds of original travel kept in either direction.
Even front and rear
VSB 14 requires front and rear to be lowered by the same amount so the car keeps its original attitude. A big rake one way or the other is outside the basic allowance.
Ground clearance: where 100mm comes from
VSB 14 requires lowered cars to keep the minimum ground and running clearances in ADR 43 and the vehicle standards. For a car, that works out to:
- 100mm within one metre of an axle
- at the midpoint between axles, one-thirtieth of the distance between axle centres
- elsewhere, enough to clear a 1:15 peak
Measurements exclude tyres, wheels, hubs, brake backing plates and flexible mudguards or mudflaps. The exhaust, sump, crossmember and front bar lip all count.
Queensland's long-standing TMR guidance puts it bluntly: road clearance of a fully laden vehicle must not be less than 100mm. That's the honest way to test. Load the car with passengers and a full tank, then measure. A car that clears 100mm empty and scrapes at 90mm with four people aboard is a defect notice waiting to happen.
Wheel and tyre clearance
This catches more lowered cars than the 100mm rule does. Under VSB 14:
- No part of the wheel or tyre may touch the body, chassis, steering, brakes or suspension in any operating condition. That's checked fully laden, lock to lock, over speed humps and driveway entries.
- If a tyre goes flat on a level road, only the rim and tyre can touch the ground. Not the exhaust, not the suspension, not the body.
- Wheels must sit inside the guards or flares when pointed straight ahead.
- You can't modify steering or suspension stops to buy wheel clearance.
Springs, coilovers and bump stops
- Springs: Lowered or replacement coil springs must have the same end shape as the originals, keep some pre-tension so they don't come loose at full droop, and leave clearance between coils at full bump.
- Cut or heated springs: NSW's suspension manual checklist asks whether coil-sprung cars were lowered "by resetting and not by other means (e.g. cutting or heating)". VSB 14 says to avoid cutting, heating, welding or bending components and to use production parts where possible. Quality coilovers or proper lowered springs are the legal path.
- Bump stops: Rubber or other resilient bump stops must be fitted wherever the suspension could bottom out on the body or chassis. Don't throw them away to get lower.
- Leaf spring blocks: Must be steel, aluminium or equivalent strength, and must locate positively on the axle spigot and spring centre bolt.
Check the knock-on effects too. VSB 14 flags driveshaft and CV angles, steering geometry, brake hose length, headlight aim, ESC calibration and load-sensing brake valves as things to recheck after a ride height change. Our first mods guide covers where suspension sits in a sensible build order.
Air suspension
VSB 14 doesn't cover driver-adjustable air or hydraulic systems, so the states handle it.
- Victoria: Airbag suspension needs a VASS approval certificate. It must keep at least two thirds of original travel in either direction and a minimum running clearance of 100mm.
- NSW: Replacing rear coils with air springs is a minor mod if height changes no more than 50mm, the original mounting points are used and the system has slow-speed controls. Other variable ride height systems need assessment, and NSW requires the minimum clearances to be held with variable suspension. The system can't adjust fast enough to unweight or bounce a wheel.
Parked on the ground with the bags dumped looks great. Driving like that doesn't comply anywhere.
State by state
| State | Key reference | What it says |
|---|---|---|
| NSW | Light vehicle modification manual: Suspension and ride height (2016) | Changes of up to 50mm are minor. Two thirds of original travel must be kept. Lowered cars need 100mm clearance in motion. |
| VIC | VSI 8 Guide to modifications | No specific lowering figure in VSI 8. Air suspension needs VASS with two-thirds travel and 100mm running clearance. Ride height changes from wheels and tyres count. |
| QLD | Queensland Road Vehicle Modification Handbook (Sept 2024) | Applies VSB 14 with Queensland variations. TMR guidance requires 100mm fully laden. |
| SA | SA roadworthy inspection rules | A roadworthy inspection is required for cars with modified brakes, steering or suspension. |
| Other states | VSB 14 | Confirm with the state authority before modifying. |
That SA rule is worth flagging: lowering beyond a straight spring-and-shock swap can trigger a roadworthy inspection there. Our what mods need engineering guide covers the wider picture.
When you need engineering
Get a certifier involved before you buy parts if you're planning to:
- drop more than 50mm in total, or past one third of the travel
- run air suspension (VIC, and anything beyond NSW's minor allowance)
- change the suspension design, such as fabricated mounts or a different model's suspension
- modify steering components
Typical cost is covered in how much an engineering certificate costs. The ballpark depends on the state, the scope and whether testing is involved.
Buying a lowered car
Measure it laden. Look underneath for scraped sumps, flattened exhaust and rubbed inner guards. Ask whether it's on springs, coilovers or bags, and whether any engineering paperwork comes with it. A car that's low and certified is worth more than one that's just low.
Rules vary between states and change over time. Confirm with your state authority or a licensed certifier before you lower.
Sources
- https://www.infrastructure.gov.au/sites/default/files/migrated/vehicles/vehicle_regulation/bulletin/files/NCOP11_Section_LS_Tyres_Suspension_Steering_Nov_2015_v4.pdf
- https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
- https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
- https://transport.vic.gov.au/registration-and-licensing/registration/standard-and-non-standard-vehicle-information/vehicle-standards-information/guide-to-modification-for-motor-vehicles
- https://www.tmr.qld.gov.au/-/media/Safety/Vehicle-standards-and-modifications/Vehicle-modifications/Queensland-Road-Vehicle-Modification-Handbook.pdf?la=en
- https://www.tmr.qld.gov.au/~/media/safety/vehicle-standards-and-modifications/vehicle-modifications/light-vehicle-modifications/pdf_modification_motor_vehicles2.pdf
- https://www.sa.gov.au/topics/driving-and-transport/vehicles/vehicle-inspections/roadworthy-inspections
Frequently asked questions
What is the minimum ground clearance for a car in Australia?
The figure everyone works to is 100mm. Under VSB 14, a lowered car must keep the minimum ground and running clearances in ADR 43 and the vehicle standards, which means 100mm within a metre of an axle. Wheels, tyres, hubs, brake backing plates and flexible mudflaps don't count.
How much can I lower my car without engineering?
Under VSB 14, up to 50mm total height change and no more than one third of the original suspension travel, with the car still meeting clearance and other requirements. NSW's suspension manual uses the same 50mm threshold. Go past that and you need certification.
Are cut springs legal in Australia?
NSW's suspension manual checklist asks whether coil-sprung cars were lowered by resetting rather than cutting or heating, and VSB 14 says to avoid cutting, heating or bending components. Treat cut or heated springs as a defect waiting to happen.
Are air bags (air suspension) legal on a lowered car?
Yes, with conditions. Victoria requires a VASS approval certificate, at least two thirds of original travel either way, and 100mm running clearance. NSW allows rear coil-to-air conversions of up to 50mm with slow-speed controls as a minor mod; other variable ride height systems need assessment.
Can I get defected for being too low?
Yes. Police can issue a defect notice if a car doesn't meet clearance or other standards, and clearing it means fixing the car and getting it inspected.




