Skip to content
Rules & Rego

LS Swaps: How to Make an Engine Swap Legal in Australia

An LS swap is one of the most common engine conversions in Australia, and one of the most commonly done wrong. Here's what the engine code requires and how to get it signed off.

8 min readUpdated 3 November 2026Horsepower House
LS Swaps: How to Make an Engine Swap Legal in Australia
In this guide

An LS swap is legal in every state if it's engineered properly. The problem is that "properly" covers a lot more than engine mounts. Emissions, brakes, noise, mass and fuel system all get assessed, and the certifier signs off on the whole car, not the motor.

Here's what the national engine code requires and how the process runs in the big three states.

Quick answer: An LS swap into anything that didn't come with one is a performance engine installation under VSB 14 Section LA (code LA2) and needs certification. Talk to a licensed certifier before you buy parts. Plan for emissions compliance, a brake upgrade with its own certification, a noise test, and an engine-size limit based on the car's mass. No nitrous. Keep the thermostat.

The national rulebook: VSB 14 Section LA

VSB 14 Section LA (Engines) is the national code for engine changes. It sorts work into four codes:

CodeCovers
LA1Equivalent engine installation: no more than 20% more mass and/or power than the original standard or optional engines
LA2Performance engine installation: more than 20% more mass and/or power
LA3Supercharger and turbocharger installation not offered by the manufacturer
LA4Engine modifications to the original or a non-original engine

An LS into a car that came with a six or a small V8 will almost always land in LA2. Boost it and LA3 applies too.

The 20 per cent rule in each state

  • Victoria (VSI 8): engine modifications giving a power increase greater than 20 per cent must be certified by a VASS signatory. Modifications that significantly increase performance or affect emissions also need VASS for passenger cars built from January 1986.
  • NSW (VSI 06): certification is required for "an engine that is not of an original family of engine for the series of models", for an engine more than 20 per cent larger than the largest original optional engine, and for increasing original power by more than 20 per cent. NSW's example: lifting a 100kW car past 120kW.
  • Queensland: TMR accepts VSB 14 with Queensland-specific variations to the engine section, and complex modifications are certified by a TMR Approved Person. Engine substitution is one of the modifications Approved Persons can approve.

What that means in practice: a VT–VZ Commodore that came with an LS1 is a different conversation from a VN with a 3.8 V6. See our VT–VZ LS1 guide if you're shopping for a factory-LS car instead.

What the certifier will check

Emissions

This is where many swaps stall. Under Section LA:

  • The modified car must comply with the ADRs that apply to it, including emissions, based on its date of manufacture.
  • Where emissions ADRs apply, emission control equipment must be retained and working.
  • An aftermarket ECU doesn't guarantee compliance "unless that particular computer/engine combination has undergone ADR emission testing".
  • Where possible, use the donor vehicle's muffler and catalytic converter.
  • Cam and induction changes mean showing continued emissions and noise compliance, under test codes LT3 and LT4.

NSW also lists non-original camshafts, carburettors or ECUs, and removing emission control equipment, as changes that need certification. A big-cam, carb-topped LS in a late-model car is the hardest possible path. A stock-spec LS with its factory ECU, cats and O2 sensors is the easiest.

Brakes

Section LA's checklists call for modified braking systems to be certified under VSB 14 Section LG, codes LG1 and LG2. Pre-ADR cars must have a split or dual braking system. The engine code also covers vacuum supply: big-cam engines may need a vacuum reservoir or pump to keep the booster working.

Engine size versus mass

VSB 14 caps capacity relative to the car's original mass, taken as the heaviest sedan version of the model:

Original massNaturally aspirated maxForced induction max
Under 800kg3.0 × mass (cc)2.5 × mass (cc)
800–1,100kg4.0 × mass (cc)2.75 × mass (cc)
Over 1,100kg5.0 × mass (cc)3.0 × mass (cc)

So a 1,200kg car could take up to 6,000cc naturally aspirated, or 3,600cc boosted. That last number is the one that catches people planning a turbo LS in a mid-size car.

Section LA also requires analysis of axles, suspension, steering, brakes and tyres if laden front or rear axle mass goes more than 10 per cent past the heaviest original model.

Installation

  • The engine must fit "without major frame, body or other modifications". Cutting the chassis or body drags in other codes.
  • Mounts must isolate vibration and handle torque. Replacement brackets don't need extra certification unless sub-frames, chassis or body members are altered.
  • At least 10mm of clearance to surrounding parts at maximum engine movement.
  • Fuel hose must be made and marked for fuel and kept clear of heat.
  • The thermostat must not be removed.
  • Nitrous oxide systems must not be fitted, even disconnected.

Noise

If the engine and exhaust come from a vehicle known to comply with the relevant ADR, the modified car is deemed to comply. Otherwise it's tested under the ADR or code LT4. More on limits in our exhaust noise guide.

The process, step by step

  1. Talk to a certifier first. Victoria uses VASS signatories, NSW licensed VSCCS certifiers, Queensland TMR Approved Persons. Agree the plan before parts are bought.
  2. Choose the right donor package. Engine, ECU, loom, cats and sensors from the same donor make emissions far simpler.
  3. Build to the plan. Expect stage inspections. Keep receipts and part numbers.
  4. Testing. Brakes, noise and, if required, emissions.
  5. Certificate and rego update. The certifier issues the approval. Then update the registration record. In Victoria, engine number changes must be notified within seven days. In NSW, a new engine may also mean a blue slip. In Queensland, a change in cylinder count is notified on form F3524.

What it costs

Typical ballpark as of 2026 for the engineering side of an LS swap, excluding the build itself, is a few thousand dollars at the low end. It climbs quickly once emissions or brake testing gets involved. What moves the number: state, vehicle age (pre-emissions cars are simpler), whether the donor emissions package is kept, forced induction, and how much fabrication was done. For general certificate pricing, see how much an engineering certificate costs. For the turbo path, see what it costs to turbo an LS.

Buying an LS-swapped car

Ask for the certificate or plate and confirm the rego record shows the new engine. An unengineered swap risks a defect notice at any roadside check and becomes a problem every time it changes hands. Our dodgy engineering cert guide shows what to look for.

Rules vary by state and get updated. Confirm the plan with a licensed certifier before you start cutting.

Sources

Frequently asked questions

Is an LS swap legal in Australia?

Yes, if it's certified. Fitting a non-original engine family, or one with more than 20 per cent more power than the original, needs certification under VSB 14 Section LA and your state's scheme, such as VASS in Victoria or VSCCS in NSW.

Do I need engineering for an engine swap?

Almost always for an LS swap. VSB 14 only allows an engine change without certification when it's an equivalent engine with no more than 20 per cent more power or mass than the original standard or optional engines. NSW requires certification for any engine outside the original engine family for that model.

What's the hardest part of getting an LS swap engineered?

Usually emissions and brakes. The car still has to meet the emissions ADRs that apply to it, and modified braking systems need separate certification and testing.

Can I put an LS in a car with a smaller original engine?

VSB 14 caps engine capacity relative to vehicle mass. For a car over 1,100kg original mass, the naturally aspirated limit is five times the mass in kilograms, in cc. That's rarely a problem for an LS in a full-size sedan, but it matters in lighter cars.

Can I run nitrous on an engineered LS swap?

No. VSB 14 Section LA says nitrous oxide systems must not be fitted, including partial or disconnectable installs.

Related guides